• Home
• Production
• Product lines

MOK-150М and MOK-300М POTATO PEELERS

PEEL PULP COLLECTOR INCLUDED!

WWW.TORGMASH-SALES.COM

The equipment is included in the Eurasian Registry of Industrial Products of the Ministry for Industry and Trade of Russian Federation.

The equipment is included in the Eurasian Registry of Industrial Products of EAEU Member States (manufacturer’s identification No. 200166490).

The company is included in the Registry of bona fide partners of BelCCI.

MOK-150М and MOK-300М potato peelers are intended for peeling potatoes and root crops (beets, carrots) at public catering facilities. They are manufactured in floor modification, with stainless steel facing.

THE MACHINES INCLUDE PEEL PULP COLLECTOR!

Since November 2016, MOK-150M and MOK-300M potato peelers have been manufactured with a new discharge door, a new locking mechanism and a new abrasive disc of high-strength low-wear material. It should be noted that the new abrasive disc does not require balancing.

The machines are manufactured in UHL4 (moderate climate) design under GOST 15150-69 for operation at temperatures from +1 to +35°С.

MOK-150М and MOK-300М potato peelers are manufactured in accordance with the requirements of STB ISO 9001-2015 and have DECLARATION OF CONFORMITY OF PRODUCTS TO THE REQUIREMENTS OF TECHNICAL REGULATIONS, Certificate of Conformity to EU Directives - CE and Uniform Sanitary-Epidemiological and Hygienic Requirements, Eurasian Economic Union Conformity Certificate (Annex).

Basic technical parameters of the machines

*- Capacity is checked at 90% of completely peeled potatoes. A tuber is considered peeled when peel remains in the recesses and in no more than three unpeeled areas (with maximum size from 1 to 3 mm) on the remaining surface (values for root crops (beets, carrots) are not specified).

Machine composition 

Composition and functionality of potato peeler

The machine consists of a housing with grid, funnel for product loading, bed plate and drive.

1 - Funnel; 2 - Housing; 3 - Grid; 4 - Door seal; 5 – Discharge door; 6 - Abrasive disc; 7 - Cuff; 8 - Tube; 9 - Shaft; 10 - V-belt (Z (0) -670Вн GOST 1284.1-89); 11 - Driven pulley; 12 - Drain hose; 13 - Lid; 14 - Screw with left-hand thread; 15 - Bearings (GOST 8882-75 180205, 180206); 16 - Cup with bearings; 17 - Drive pulley; 18 - Belt tensioning bolt; 19 - Electric motor; 20 - Casing; 21 - Nipple coupling; 22 - Control panel; 23 – “START” button; 24 - Indicator; 24 – “STOP” button; 26- Bed.

Machine functioning is based on peeling potatoes and other root crops by mechanical action of peeling tools.

Turn ON the machine by pressing “START” button on control panel. Pour water into the housing through the funnel hole providing total consumption of no more than one liter of water per kilogram of the product to be peeled (water pressure - 260 kPa).

Open the funnel lid and load the previously washed and peeled product into the housing. Close the lid. Clean the product and ensure that peel pulp and water is drained from the machine.

After the end of peeling process, place a container for collecting the peeled product under the tray of discharge door, turn OFF water supply to the housing, carefully open the discharge door and unload the peeled product. Peeling efficiency should be checked visually.

Peel pulp is removed through the hole in the bottom of the machine through drain hose.

After discharging the entire portion of the product, close the discharge door. To peel the next portion of the product, repeat the operations. At the end of peeling, turn OFF the machine by pressing “STOP” button on control panel, and stop water supply to the housing.

At the end of operation, turn circuit breaker OFF.

The peeled product should be finally peeled by hand (removing “eyeholes” and remaining peel).

The machine should be kept clean and assembled. It is allowed to use hair brushes and rags for cleaning.

Transportation

The machine should be transported from the place of receipt to the place of installation and mounting in factory package. After machine unpacking, check delivery set in accordance with paragraph 1.3 of Operating Manual.

Mounting

The place of machine installation should ensure safety and ease of operation and maintenance. It should comply with sanitary standards, fire safety requirements, labor safety instructions and mounting guide.

The machine should be installed on a foundation 100 mm above floor level and should be secured with four M12 anchor bolts.

1 - MOK-150M or MOK-300M machine; 2 - Automatic circuit breaker; 3 - Cold water supply; 4 - Rubber hose; 5 - sewerage

All the works upon machine connection to power line and putting it into operation should be performed by a representative of servicing company in accordance with “Electrical Installations Code”, “Rules for Operation of Consumers’ Electrical Installations” and “Cross-industry Labor Safety Regulations” applicable in the Republic of Belarus or in accordance with similar applicable regulations of importing country. 

Warranty liabilities

Warranty period is 24 months. It starts from the day of putting the machine into operation, but not later than 6 months from the date of machine purchase.

Manufacturing company shall eliminate equipment malfunctions during warranty period, provided that the following conditions are obfed:

1. Observance of all the requirements of the “Operation Manual” regarding the machine.
2. Mounting and putting into operation is performed by specialists of servicing company or by specialists of another company under written permission of the manufacturer.
3. Handing over (sending) a copy of properly drawn-up “Act of putting the machine into operation” to manufacturing company within 10 days from the day of putting the machine into operation in order to provide warranty registration.
4. Performing monthly maintenance under the “Operation Manual”.
5. Handing over (sending) a copy of properly drawn-up “Damage Claim”.

Monthly maintenance operations in accordance with the requirements of the “Operation Manual” are NOT warranty maintenance and should be performed at consumer’s expense by specialized companies under a preliminary agreement.

In case of violation of at least one of the aforementioned conditions, the manufacturer disclaims their warranty liabilities.

Note: the drawn-up “Act of putting the machine into operation” and “Damage Claim” shall be stamped by a consumer and by the company putting the machine into operation or performing its repair and maintenance.