ONION PEELER! MOK-400L ROOT CROP PEELER

PEEL PULP COLLECTOR INCLUDED!

MOK-400L root crop peeler is intended for peeling of onions and other root crops by mechanical action of peeling tools at public catering facilities. It is manufactured in floor modification, with stainless steel facing.

One-piece housing design!

It is manufactured with a new discharge door, a new locking mechanism and is equipped with a special abrasive disc made of high-strength low-wear material. It should be noted that the new abrasive disc does not require balancing.

The peeler is manufactured in UHL4 (moderate climate) modification under GOST 15150-69 for operation at temperatures from +1 to +35°С in accordance with the requirements of STB ISO 9001-2015 and has Eurasian Economic Union Conformity Declaration (Annex)Certificate of Conformity to EU Directives - CE.

 

Basic technical parameters of the machine

Parameter description

MOK-400L

Performance (kg/h, minimum*)

260

Peeling efficiency (%, minimum*)

80

Volume of simultaneously loaded product (kg, maximum*)

8.5

Percentage of product waste during peeling (maximum*)

32

Rated power consumption (KW, maximum)

0.78

Installed power (KW)

0.55

Overall dimensions (mm, maximum):

length

width

height

 

595

530

830

Power supply:

current type

rated voltage (V)

current frequency (Hz)

three-phase

alternating

400

50

Cold water flow (l/kg, maximum*)

1.5

Processing cycle duration (sec., maximum)

85/70

Weight (kg, maximum)

40

Control unit


Upper lid

Remote panel

Electrical interlock

- Performance is tested at 90% of completely peeled product. The peeled product should have no more than three areas with peel residues with the maximum size not exceeding 11 mm. Onions may have slight scratches after peeling.

Machine composition

Designation

Description

Quantity per one machine

MOK-400L

MOK-400L

Root crop peeler consisting of: grid, disc 

1

 

Wire ПВС 4х1.0+1.0, black (or another similar for machine connection to automaic circuit breaker), overall length (m)

3.6

Note:

for machine connection to automaic circuit breaker

МС-3

Peel pulp collector

1

Set of mounting parts

 

Anchor bolt with nut 10х50 (pcs.)

4

Filling hose (1 m)

1

Input device with automatic circuit breaker of type ВА 47-29, 400V, ~50 Hz, 3 poles, 2.0 А, time-current characteristic “С”, ТУ 2000 АГИЕ.641.235.003

Automatic circuit breaker of specified type is an integral part of the machine. Non-fulfillment of this requirement may cause damage to the machine.

1

Note: optional

3SD6 exposed installation cabinet with “zero bus” and ground bus for three-pole circuit breaker

1

Note: optional

Set of package

 

Package box

1

Documentation

MOK-400L OM

Operation manual

1

MOK-400L D1

Quick user’s guide for root crop peeler

1

(included in OM)

MOK-400L D2

Safety instructions for root crop peeler usage

1

(included in OM)


Additional functions

For processing potatoes and other root crops, grid MOK-400.50.000it should be purchased and mounted. Mounting of this grid does not require additional tools or machine modification.

Parameter description

MOK-400L

Performance (kg/h, minimum*)

460

Peeling efficiency (%, minimum*)

90

Volume of simultaneously loaded product (kg, maximum*)

11

Percentage of product waste during peeling (maximum*)

17

*- Parameters are defined using potato. Capacity is checked at 90% of completely peeled potatoes. A tuber is considered peeled when peel remains in the recesses and in no more than three unpeeled areas (with maximum size from 1 to 3 mm) on the remaining surface. 

Composition and functionality of root crop peelers

The machine consists of a housing with grid, lid, motor and peel pulp collector.

МОК-400Л

1 - Housing; 2 - Lid; 3 – Control unit; 4 – Grid; 5 - Disc; 6 - Shaft;

7 - Drive; 8 – Electrical equipment; 9 - Bracket; 10 - Peel pulp collector; 11 - Drain tube;

12 - Nipple adapter; 13 – Discharge hatch; 14 – Illuminated “Start-Stop” button

Machine operation is based on peeling potatoes and other root crops under mechanical action of working tools.

Machine operation is based on removal of peel from onions and other root crops by mechanical action of peeling tools.

Water is supplied to the housing Through a hose with a nipple. Total consumption: not more than one and a half liters of water per kilogram of the product to be peeled (water pressure - 260 kPa).

Opened the lid for feeding and load the previously washed and cleaned product into the housing (peel the onion to stems and necks). Close the lid. Supply water. Use time relay knob to set the required operating cycle time. Switch ON the machine by pressing “START” button.

Peel the product and ensure that peel pulp and water are drained from the machine. It is necessary to clean the grid of the peel pulp collector.

After the end of the peeling process, place a container under discharge door to collect the peeled product, shut off water supply, carefully open the discharge door and unload the peeled product. Efficiency of peeling is shecked visually. 

At the end of operation, turn circuit breaker OFF.

The machine should be maintained clean and entirely assembled. It is allowed to use hair brushes or cloth for cleaning. Handle disc with care when sanitizing manually.

Transportation

The machine should be transported from the place of receipt to the place of installation and mounting in factory package. After machine unpacking, check delivery set in accordance with paragraph 1.3 of Operating Manual.

Mounting

The place of machine installation should ensure safety and ease of operation and maintenance. It should comply with sanitary standards, fire safety requirements, labor safety instructions and mounting guide.

The machine should be installed on a foundation and secured with four M12 anchor bolts.

Монтаж МОК-400Л

All the works upon machine connection to power line and putting it into operation should be performed by a representative of servicing company in accordance with “Electrical Installations Code”, TKP 181-2009 “Rules for Operation of Consumers’ Electrical Installations” and “Cross-industry Labor Safety Regulations” applicable in the Republic of Belarus or in accordance with similar applicable regulations of importing country. 

Warranty liabilities

Warranty period is 24 months. It starts from the day of putting the machine into operation, but not later than 6 months from the date of machine purchase.

Manufacturing company shall eliminate equipment malfunctions during warranty period, provided that the following conditions are obfed:

  1. Observance of all the requirements of the “Operation Manual” regarding the machine.
  2. Mounting and putting into operation is performed by specialists of servicing company or by specialists of another company under written permission of the manufacturer.
  3. Handing over (sending) a copy of properly drawn-up “Act of putting the machine into operation” to manufacturing company within 10 days from the day of putting the machine into operation in order to provide warranty registration.
  4. Performing monthly maintenance under the “Operation Manual”.
  5. Handing over (sending) a copy of properly drawn-up “Damage Claim”.

Monthly maintenance operations in accordance with the requirements of the “Operation Manual” are NOT warranty maintenance and should be performed at consumer’s expense by specialized companies under a preliminary agreement.

In case of violation of at least one of the aforementioned conditions, the manufacturer disclaims their warranty liabilities.

Note: the drawn-up “Act of putting the machine into operation” and “Damage Claim” shall be stamped by a consumer and by the company putting the machine into operation or performing its repair and maintenance.